Barr Mullin Wondersaw Optimizer with Computerized Laser Controls Tichniess: Up to 3" Width: 31" Min cut: 4" Feed height: 34-1/2" Floor Space: Apprx 21' x 15' 480 volt

Brewer BR8112 Double Arbor Gang with Sizer 12" Wide Capacity 75 HP Top Arbor 75 HP Bottom Arbor 30 HP Sizer 480 V/3Ph Seller purchased this and never used it. Includes the following that was never installed: Controls and starters, VFD for infeed, rollers, bottom arbor, some new bearings,

10 HP 3200 rpm main motor 2.7 HP feed motor Variable feed up to 262 fpm 18” blade 30 mm arbor 460 volt 3-phase

Cardinal Gang Rip Saw 6" Double Arbor Infeed 3-Rolls on top, 3-rolls on bottom (2) 125 HP Motors

Cornell Double Arbor Gang Saw

Per seller: This saw was used as more of a center splitter. It has been used to gang rip 2x6 into 2x3.

The seller has upgraded to a new machine and no longer needs this rip saw. This machine still runs a few times a week at the shop. 15 HP Motor 2 HP Feed Motor 2" Arbor 16" Max blade capacity Chain drive

Diehl Model 75 Straight Line Rip Saw Chain is in good shape. Left and right chains are worn evenly. Includes: Laser Variable Speed: 4-speeds

Griggio C250 Rip Saw 250 mm Wide belt (10")

This system was purchased used and never put into service.

Mattison 404 Rip Saw Seller was using until they upgraded to a gang rip. Ready to ship.

Madison 202 Straight Line Rip Saw

Mereen Johnson Model 312 Rip Saw Includes: New pads for the chain Includes: Twistlock Collar Mounted Saw Blades Available approx May 1, 2024

Mereen Johnson Model 312 DC SR1R Rip Saw 600 V/3 PH/60 Cy

Mereen Johnson 424 DC Gang Rip Outfeed Rollers

These two rip saws were removed from service in working condition some time ago. The seller purchased them and never installed them. They have been in storage the whole time.

Mereen Johnson 424 DC/SR4 Gang Rip Saw with Automated Infeed with multiple lasers manufacturer’s specs to be confirmed 24” width capacity 3-1/2” thickness capacity 75 HP main motor 3 hp feed motor feed rete 30-245 fpm

Mereen Johnson 431 DC

Newman Whitney KF-24 Gang Rip Saw

- Close link chain vs. open (no dust or pinch point) - Oiler has twice the number of lube points (critical) - The VS adjustment location on the 14N. - Can cut up to 4 15/16? with 14? blade vs. the MRS-12 12? blade 3-15/16”. - Can run 12? as well on the MRS-14N - Bottom kickback fingers for added safety - Saws, with proper tooling and material, can glue line Specifications: - Main Motor Hp. = 50 Hp. - Voltage/ Freq. = 460 Volt 60Hz - Phase = 3 Phase - Amp Requirement = 35 Amps - Feed Hp. = 2 Speed 1.5 / 3 Hp. - Feed System = Feed Chain - Feed Speed = 25 – 120 FPM - Variable Speed = Variable Speed Pulley - Elevation Hp. = 1/4 Hp. - Elevation Style = Manual Wheel Adjustment - Elevation Sys. = Jack Screw / Linear Guides - Total Hp. = 53.25 Hp. - Electronics = CE Approved Components - Dual Voltage = Elevation Arbor Motors - Control Voltage = 110 Volt - Assisted Start = Wye-Delta - Pass-Line = 33-1/2” - Min. Length = 17-3/4” - Min. Width = 1/2” - Max. Width = 27-1/8” - Min. Thickness = 5/16” - Max. Thickness = 4-15/16” - Arbor Rpm = 3570 Rpm - Blade Size = 12” Tungsten Carbide Tipped - No. of Teeth = 36 Tooth - Blade Kerf = 3.5 mm - Cleaning System = Brush on Chain - Vertical Travel = 3/8” – 5” - Dust Collection = (2) 6” @ 1962 CFM - Arbor Diameter = 70 mm - Hold Down Style = Pressure Plate - Kickback Finger = (2) Top (1) Bottom Sets - Emergency Stop = Push Button - Rear E Stop = Push Button - Safety Feature = Safety Interlock Switch - Guarding = Full Cabinet Enclosure - Oiler = Automatic Mechanical Oiler - Low Oil Warning = Low Oil Shut-off - Fence Type = Adjustable - Fence Dims. = 103” Length - Frame Const. = 5/16” Steel Construction - Worktable Dims. = 27-1/8” x 64” - Infeed Table = 13-3/4” x 103” - Decible Rating = 74 dB - Net Weight = 4402 Lbs. - Gross Weight = 4694 Lbs. - Machine Dims. = 67” x 58” x 71” - Packaging Dims = 72” x 65” x 77”